• Visit Rebornbuddy
  • Why does HB stop running occasionally?

    Discussion in 'Archives' started by lastdayx52, Feb 7, 2010.

    1. lastdayx52

      lastdayx52 New Member

      Joined:
      Feb 3, 2010
      Messages:
      133
      Likes Received:
      0
      Trophy Points:
      0
      The bot runs for a bit, stop for half a sec, runs again, stops again for half a sec, etc.

      Why does it do that? Can I make it just keep going to make it smooth travel?
      No targeted mobs, no mobs near the bot at the time, etc. It just does it :/
       
    2. hokumera

      hokumera New Member

      Joined:
      Jan 18, 2010
      Messages:
      152
      Likes Received:
      0
      Trophy Points:
      0
      If you have the auto equip plug-in enabled, try disabling it. That should do the trick.
       
    3. mulla

      mulla New Member

      Joined:
      Jan 15, 2010
      Messages:
      23
      Likes Received:
      0
      Trophy Points:
      0
      Mine also does it on 2 different computers. i dont have autoequip enabled. It actually did it just as i was writing this, so adding the log.
       

      Attached Files:

    4. Kickazz006

      Kickazz006 Well-Known Member Moderator

      Joined:
      Jan 15, 2010
      Messages:
      20,567
      Likes Received:
      302
      Trophy Points:
      83
      as far as addons go, on my GB accts i only use bagnon and postal
      on my HB acct(s) i use bagnon, postal, and lootfilter (for deleting fish scales, light feathers, green hills and crap like that)

      but... here is what i get from your log:
      Code:
      [8:42:04 AM:68] [Navigator (Horde1-60.mesh)]: Changed destination! Last: <NaN, NaN, NaN>, new: <-1558, -2681, 92>
      [8:42:04 AM:233] [GeneratePath (Horde1-60.mesh)]:[B][U] [COLOR=darkred]WARNING: Suitable end node is more than 25 yards away from the destination point (exact distance is 53.43067 yards)![/COLOR][/U][/B] Please append to your mesh if this gives you any problems.
      [8:43:10 AM:517] Stopping Honorbuddy.
      [8:43:10 AM:529] Thread was being aborted. - From: mscorlib at System.Threading.Thread.SleepInternal(Int32 millisecondsTimeout)
      at System.Threading.Thread.Sleep(Int32 millisecondsTimeout)
      at Styx.FiniteStateMachine.Engine.HandleExit(Object )
      and then you stopped it... get closer to your mesh and then start it? also, is your pull distance set at 30+?
       
      Last edited: Feb 7, 2010
    5. Kickazz006

      Kickazz006 Well-Known Member Moderator

      Joined:
      Jan 15, 2010
      Messages:
      20,567
      Likes Received:
      302
      Trophy Points:
      83
      also:

      [8:41:22 AM:970] Foodname:
      [8:41:22 AM:985] Drinkname: Ice Cold Milk

      ^^ do you have milk in your bags? if not, that will make your toon sit for a long time after each pull. if this is NOT the case, what you need to do is check the debug and navigation logs while its doing this "error" that you speak of and let us know what it says
       
      Last edited: Feb 7, 2010
    6. mulla

      mulla New Member

      Joined:
      Jan 15, 2010
      Messages:
      23
      Likes Received:
      0
      Trophy Points:
      0
      Pull distance is 27. I can not understand why it should need to be closer to the mesh. At the point where it stopped for that sec, it had been running by itself for a couple of min. That would mean it ran too far away by itself?

      Yes, there was Ice Cold Milk in the bag. But that could still not have anything to do with the bot stopping and pause for a sec while traveling. It had no need to drink when it stopped.
       
    7. Kickazz006

      Kickazz006 Well-Known Member Moderator

      Joined:
      Jan 15, 2010
      Messages:
      20,567
      Likes Received:
      302
      Trophy Points:
      83
      well some meshes let me be over 100 yards away, some dont like more than 25. i really dont know, maybe hawker will, but test it out and see what your other errors are in the other 2 tabs. if it spams "too far" then you are... well, too far. keep us updated
       
    8. mulla

      mulla New Member

      Joined:
      Jan 15, 2010
      Messages:
      23
      Likes Received:
      0
      Trophy Points:
      0
      Well i just restarted to test again. Started the bot the same place as last time, and it happened again. However, i cant find anything in the log or the taps that could lead me to the problem. The distance to the mesh error, seems to be right after he enters ghost wolf, and where he stops is maybe 30 sec 1 min away from there. So i have no idea, why he stops :(
       

    Share This Page